Insite Pacific Pegasus camera software!!!!

This topic has 24 replies, 8 voices, and was last updated 11 years, 2 months ago by Bryan Flaherty.

Viewing 15 posts - 1 through 15 (of 25 total)

1 2 →

Author

Posts
November 21, 2008 at 12:37 pm #1991

Savante
Participant

I have a y-c camera that appears to be over driving the video signal into my fibre optic mux. Thing is fuzzy. (I think this may be the same problem as oor buddy with the falcon!)

There is apparently some rs-232 software that can be used to communicate with the camera and control amplification at a key-stroke.

Buggered if I know where the cd-rom is and we don’t have a manual. I’ve tried tom at insite pacific, but it’s about 3am. Their web-site may have a download section, but none of the links are active.

Grrr. If anyone has a copy of the software and the pegasus manual, could you please email it to

Cheers,

Sav.

November 21, 2008 at 12:48 pm #20500

Savante
Participant

bump!!

November 21, 2008 at 4:24 pm #20501

pipetracker
Participant

Grant. You have mail

November 21, 2008 at 4:54 pm #20502

Savante
Participant

heh heh, much obliged !!

November 21, 2008 at 5:25 pm #20503

Scott Beveridge
Participant

And again dude…

November 21, 2008 at 8:28 pm #20504

James McLauchlan
Participant

Was that a result?

November 21, 2008 at 8:55 pm #20505

Savante
Participant

aye, recieved in good order! And much faster than tech support direct !! Possibly you might have a "hosting" of software opportunity here James, if the manufacturers can be agreeable.

November 22, 2008 at 2:19 am #20506

Scott Beveridge
Participant

Guys,

Maybe one better…. How about a tech library?? Heaven knows, I’ve got a truckload (electronically) that I’m quite willing to share! (Within propriety rules and regs – of course….)

November 22, 2008 at 6:06 am #20507

Savante
Participant

works for me, the amount of times I’ve hunted for that Kongsberg digital camera software only to find some moron has been using the CD for a coffee coaster !!

For god sake, we have cupholders!! 😯

November 22, 2008 at 7:47 am #20508

Savante
Participant

can of worms has been opened here I’m afraid and I’m not too proud to ask !!!

Just got up, installed the software, and whilst I can exit auto focus to remote focus using the focus control switch down for 2 secs, I can’t initiate the long drive amplifier settings "setup" mode.

What’s supposed to happen is you hold focus and zoom simultaenously for 15 seconds and the camera will telephoto-wide lens to imply it is in a different "setup" mode .

Trouble is I think our control shack is only capable of sending a single signal to the camera at a time. i.e cannot send simultaneous zoom \focus commands…..

anyone got a quick fix or am I going to have to rig up a 5V ref and re-wire this bucket of bolts\paper weight…

I don’t think our control stuff is truly multi-taskin. I am trying to use buttons from two control chairs using my baboon arms as we only have a single mouse per pilot !!

Hell of a morning to start drinkin noggy coffee again !! nobody panic !!!! 😆

online in realtime

November 22, 2008 at 9:43 am #20509

Savante
Participant

only thing i can think of at the moment is short+circuiting out the line driver circuit….. anyone tried that??

SB12 and SB11 solder over 1 and 2 on mobo??

November 22, 2008 at 10:23 am #20510

James McLauchlan
Participant

Topic moved to Technical discussions.

November 22, 2008 at 5:36 pm #20511

Savante
Participant

solution was to confirm that SB13 is correctly configured to Y\C or composite video output.

In addition, to remove the line amplifier completely, solder SB11 and SB12 across.

Then remove the connection completely to board OB1500. This has to be done or the video stays corrupted.

If you have grey-out, it is possible that whilst SB11 is soldered across, SB12 is not !!

Thing works for the moment……

November 23, 2008 at 1:07 pm #20512

ronjon
Participant

If there is still a copy of the discussed software and pegsus manual available I would appreciate a copy of it.
I am having similar issues with a pegasus camera possibly over driving a focal 903 mux resulting in overbright topside pictures, it also seems that either the overlay or HDD/DVD player are overamping the signal anyone had a go at adjusting the gain in a pioneer HDD/DVD player before?

November 23, 2008 at 4:01 pm #20513

Savante
Participant

ronjon, whilst the solution i posted works for us, I havent had a chance to discuss with tony from insite, so "operator beware" !!

PM me your address and I’ll onpass.
Author

Posts